Heidolph Hei-VAP Precision User Manual Page 46
- Page / 59
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Errors and Troubleshooting Errors and Troubleshooting
90 91
Hei-VAP Precision
Error / message
error text
Cause Remedy
The temperature sensor
for calculating the vapor
temperature is not
connected, defective or
the temperature is above
the measured range.
‒ Vapor sensor broken
‒ not connected
‒ above the temp. range
Let the boiling temperature
sensor cool
Connect the vapor
temperature sensor
Perform visual check
Contact service
The vapor temperature
sensor is defective or the
temperature is below the
measured range
‒ Short circuit of the vapor
sensor
‒ below the temp. range
Heat the boiling
temperature sensor
Perform visual check
Contact service
The Auto
accurate
sensor
is defective or the
temperature is below the
measured range.
‒ Auto
accurate
sensor short circuit
‒ below the temp. range
Heat the Auto
accurate
sensor
Perform visual check
Contact service
The Auto
accurate
sensor
is defective or the
temperature is above the
measured range.
‒ Auto
accurate
sensor is broken
‒ not connected
‒ above the temp. range
Let the Auto
accurate
sensor cool
Connect the Auto
accurate
sensor
Perform visual check
Contact service
The transportation
protection device is active,
please raise the lift and
briey switch the unit off
and then on again.
‒ The transportation protection
device is still activated.
Please raise the lift and
briey switch the unit off and
then on again.
An error occurred in the
data bus.
‒ Cable connection between
the control panel and the
base unit was disconnected.
An error occurred in the data
bus.
Restore the cable
connection between the
control panel and the base
unit. Switch the power
switch off and on again!
Contact service
The overheating
protection was triggered
or the heater is defective.
‒ Heater is defective, i.e. the
overheating protection was
triggered.
If the medium was in the
heating bath: Let the heating
bath cool and reset the
maximum tem-perature
limiter
If the medium was not in
the heating bath: Contact
service
Error / message
error text
Cause Remedy
A temperature above the
safety temperature was
measured in the heating
bath. The temperature
measurement is defective
or the medium lled in
was too hot.
‒ Heating bath safety
temperature is exceeded
Switch off units
Cool the heating bath
medium
Contact Service if media was
not lled in
The heating bath is
completely evaporated.
Please rell the heating
bath medium.
‒ Heating bath is completely
evaporated.
Deactivate the unit
Check if the maximum
temperature limiter has
responded. If yes, reset
(see chapter “Maintenance,
cleaning, service” –
“Maintenance”)
Fill in heat transfer uid
An illogical temperature
difference was measured
between the heating bath
sensors. The temperature
measurement is defective.
‒ Heating bath sensor variance
> 10 K
Contact service
The temperature sensor
for the heating bath
control is defective.
(hardware monitoring
unit)
‒ Sensor monitoring via
hardware
‒ Heating bath sensor is broken
or short circuited
Contact service
The temperature sensor
for the heating bath
control unit is broken or
bath medium that is too
hot was lled in.
‒ Heating bath sensor is broken
‒ Heating bath is more than
217 °C
Contact service
The temperature sensor
for the heating bath
control unit is defective or
bath medium that is too
cold was lled in.
‒ Heating bath sensor short
circuit
‒ Heating bath is below 0 °C
Switch off units
Cool the heating bath
medium
Contact Service if media was
not lled in
The lift motor is defective
or blocked.
‒ Lift end stop switch is not
reached after 10 seconds.
Contact service
- Precision 1
- Contents 2
- Versions references 3
- About this manual 3
- About this Document 4
- Structure of warnings 4
- Mandatory signs 4
- Warning signs 4
- Verbotszeichen 5
- Other icons and symbols 5
- General Safety Instructions 6
- Intended use 6
- Qualications of Personnel 7
- Safety Conscious Working 7
- Signs on the equipment 8
- Remaining hazards 8
- Basic safety instructions 9
- Unit Description 10
- Scope of delivery 10
- Transport 11
- Setting up the basic unit 12
- Start-up 13
- Glassware sets 14
- Install the vapor tube 15
- Figure 4-8: Locking button 16
- Install the condenser 17
- Install the evaporator ask 19
- Insert the inlet tube 21
- Assemble the inlet tube 22
- Assemble the collecting ask 22
- Connect the vacuum 22
- Feed the distilled material 26
- Ventilate manually 26
- Figure 4-3: Connections 29
- Switching on the base unit 30
- Operating the control panel 30
- Operation Operation 31
- Operating the lift 32
- Setting the language 33
- Menu display 35
- Actual value display 35
- Timing functions 38
- Gradient function 39
- Softkeys 40
- More Functions 41
- Setup Menu topology 42
- Gradient 43
- General errors 44
- Additional conditions 45
- Hei-VAP Precision 46
- Maintenance 48
- Replacing the fuses 49
- Cleaning 50
- Disassembly 50
- Disposal 51
- Spare Parts 52
- Accessories 54
- Technical data 55
- Unit conguration 56
- Solvent data 57
Related products and manuals for Equipment Heidolph Hei-VAP Precision
Equipment Heidolph Rotacool User Manual
(15 pages)
(15 pages)
Equipment Heidolph RotaChill User Manual
(37 pages)
(37 pages)
Equipment Heidolph Rotacool Mini User Manual
(104 pages)
(104 pages)
Equipment Heidolph Vacuum Switchbox User Manual
(188 pages)
(188 pages)
Equipment Heidolph LABOROTA 4000 eco User Manual
(168 pages)
(168 pages)
Equipment Heidolph LABOROTA 20 eco User Manual
(180 pages)
(180 pages)
Equipment Heidolph ROTAVAC 20 User Manual
(35 pages)
(35 pages)
Equipment Heidolph MR Hei-Tec User Manual
(39 pages)
(39 pages)
Equipment Heidolph MR Hei-End User Manual
(124 pages)
(124 pages)
Equipment Heidolph MR Hei-Mix D User Manual
(24 pages)
(24 pages)
Equipment Heidolph MR Hei-Mix S User Manual
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 0.872 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals